Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - bryan.a.white

Pages: [1]
Upgrades and Modifications / Re: Olympian Heater Install
« on: March 22, 2017, 11:05:57 AM »
A little heat- propane torch will soften up even the permanent locktite and let you remove the fitting. Too late, I know ;-).


I tried that, wouldn't budge. My little heat turned into a little too much and the hoses melted. I tried heat gun to start slow, then went to a propane torch. Nothing doing.

Upgrades and Modifications / Olympian Heater Install
« on: March 21, 2017, 06:36:05 PM »
Fellow QuickSilver Owners.

We do a lot of the grid boondock camping/fishing/boating in colder weather up here in Washignton State. Regularly in the 20's at night in the spring and the fall. The batteries don't last long with the furnace cycling every and running in cold temps and I HATE generators while sleeping (or any other time for that matter). So I bit the bullet and installed a Camco Olympian Wave 8.

Thought I would share my experiences with the heater install.

Step 1- Found a place to plumb in supply line. This was a tricky step as I found out. The propane manifold located near mid-trailer under the floor seemed optimal as it had a 3/8" NPT plug that I was hoping to remove and tap into. However, it became evident after my point of no return that the supply lines were Locktite glued in place and I couldn't remove the plug in place and had to rebuild the manifold. This involved a lot of fittings and some real thinking about reassembly. The original supply lines were male NPT and changed them to a swivel female for assembly purposes.

Step 2- In order to get this whole thing done I had to cut each of the supply lines and crimp new fittings on each end. I borrowed a crimper and went down to the local hose shop and got the parts. This step was a huge P.I.T.A. Had the plug been removable none of this would have been necessary. I'm not sure why these lines cannot be removed from the factory. Maybe there is something to them coming loose after driving or something, but it would not budge.

Step 3- I plumbed the supply line to the quick disconnect inside. The Camco Wave 8 heater can be mounted or on feet. I wanted to move it around and have a quick disconnect for storage under the front bed. Using a 3/8" Nipple Supply Kit purchased on Amazon, I was able to clamp the nipple to the floor solidly to support the quick disconnect on the inside of the trailer.

Step 4- Plumb supply line to the heater which is 3/8" flare male. I chose a 10' hose to allow me to set the thing anywhere out of the way.

Hope this is helpful to somebody looking to put one of these in. After running it, I couldn't be happier. Seems like less propane consumption and we were comfortable in the low 30's with the unit running on low. Inside temperature hovered around 60 with the furnace cycling once every hour or so.

New Members / Re: Greetings from The Evergreen State
« on: March 21, 2017, 05:55:32 PM »
Spokane here. Sure don't see a lot of Livin Lite's around this part of the country. Whenever I see one I have to do a double take.

QuickSilver Toy Haulers / Re: Insulating Floor
« on: January 19, 2017, 05:39:24 PM »
Fantastic idea about the floormats...I like the idea of insulating the inside and maintaining wash-ability of the underside.

QuickSilver Toy Haulers / Insulating Floor
« on: January 13, 2017, 01:08:04 PM »
We are hoping to extend our season in the VRV, and as most probably know in cold weather that floor is cold. We are using rugs and other floor covering, but I am wondering if anyone has explored insulating the floor. I'm thinking of a closed cell spray foam. Whatever the solution, I don't want it to get saturated with water. I'm looking for a durable high quality option. I don't want to just stuff something half baked up there and hope for the best.

Any thoughts from the group?

New Members / New Old and New Again Member
« on: January 13, 2017, 12:24:29 PM »
Saying hi to the group, I was a member on the old board...although mostly a reader. I picked up a 8.5x24 VRV last year and am still breaking it in. Looking forward to the new board and sharing adventures!

Pages: [1]